關注大連防水施工了解行業熱點資訊

  在進行防水處理之前，一定先找平地面，如果地面不平或效果不好，可能造成因防水涂料薄厚不均而導致的開裂滲漏。地漏，墻角，管跟等接縫處要使用高彈性的柔性防水涂刷，因為衛生間的墻與地面之間的接縫處會移位最容易滲水。防水是隱蔽工程，后續的施工也有可能會破壞防水層，如果地磚已鋪設完畢，可千萬不要砸地磚，用專業的補縫防水材料，把所有的縫隙堵住做好防水就好了。也同樣適用于衛生間防水層失效后防水工程 。

  衛生間各種下水管能不改動，盡量不要去改動；萬一要改動，千萬不能用水泥沙漿去填孔隙，一定要堵漏王分三次去填。房間最容易漏水的是下水管四周和墻角四條邊，因此這些重點部位應該予以格外重視。地面四周也要分成三次堵，要有間隔時間。這樣，就給地面穿了一層剛性的防水盔甲。衛生間門檻內要做一個斜坡，涂得高，防止水倒流到外面房間去，并且門檻石一定要用精水泥 沙漿稍微放點堵漏王濕貼。高分子卷材如用焊接法連接，卷材搭接部位采用熱風槍雙焊縫加熱焊牢，焊縫寬度不小于10mm，且均勻連續，不得有假焊、漏焊、焊焦、焊穿等現象。焊接時，必須先熔去待搭接部位卷材上表面的防粘層和粒料保護層，同時應采用熱風槍熔化接縫兩面的粘接膠，然后進行粘合、排氣、封口。對粘貼好的卷材接口，采用熱風焊接，同時用專用滾筒將接口按壓密實。